Apartments & property management

Know about a leak before a resident tells you

Lark Alert is leak and temperature sensors plus alerts for maintenance teams — in units, in vacant units, and in the mechanical and boiler rooms that feed them — with every building and site in one place in the Lark Alert iPhone app.

  • Leak and temperature sensors across buildings and sites
  • Instant push alerts to the Lark Alert iPhone app, after hours included
  • Incidents stay open until a person acknowledges and closes them

Illustration of the Lark Alert iPhone app.

What apartment operators are up against

Water is the loss that multifamily owners and managers deal with most, and detection is still rare. The figures below are industry and insurance data.

These figures are industry context from insurers and industry groups. They describe water risk across the market — they are not Lark Alert results, and nothing here is a claim about what Lark Alert will detect or avoid at your properties.

How it works

Three steps. Nothing to migrate, nothing for residents to install.

  1. Place sensors where water shows up

    LoRaWAN leak sensors — for example, the Dragino LWL02 — go beside water heaters, under washers, and in mechanical and boiler rooms. Temperature sensors watch the spaces you don't want getting cold.

  2. Your team gets alerted on their phones

    When water reaches a sensor, an instant push alert goes to the Lark Alert iPhone app, so your maintenance team gets it on their phones at 2 a.m. as readily as at 2 p.m.

  3. Close the loop

    The incident stays open until a person acknowledges and closes it, and a sensor that goes quiet is flagged with an offline-sensor alert.

Where sensors go in a community

The places water starts in multifamily buildings are predictable, and most of them are rooms nobody walks through daily.

In-unit water heaters and washers

Tanks, supply hoses, and washer standpipes are the classic in-unit failures, and the unit below is the one that pays for them.

Vacant and turnover units

Nobody is in the unit to notice a line that lets go between residents, so a vacant unit can run for days.

Mechanical and boiler rooms

Pumps, risers, and boilers sit behind a locked door that gets opened on a schedule rather than when something goes wrong.

Common laundry

Shared laundry runs all day and drains constantly, and the floor is usually above something you care about.

HVAC and roof

Condensate pans and rooftop equipment drip into the top floor's ceiling long before anyone reports a stain.

Freeze watch

Temperature sensors in vacant units, stairwells, and mechanical spaces alert you when a space drops below the low limit you set.

Every building in one view

Organizations and sites group every sensor by property and building, so the Lark Alert iPhone app holds every building and site in one place — including the sensors that have gone quiet.

Riverside Properties — all sites6:05 AM

Building A

12 sensors · All clear

Building B

9 sensors · 1 alert

Building C

14 sensors · 1 offline

Illustration of a view in the Lark Alert iPhone app. Sites, buildings, and sensor counts are examples.

What that changes for your team

Lark Alert doesn't stop a pipe from failing. It makes sure the failure isn't the first thing a resident tells you about.

Less damage to chase

A leak someone knows about is a leak someone can go deal with. The sooner the alert lands, the less water has moved.

Less disruption for residents

Water that gets handled in a mechanical room is water that didn't go through somebody's ceiling.

Fewer after-hours surprises

Nights, weekends, and empty units are when leaks run unnoticed. An alert on your team's phones beats a call from a resident.

Questions from property teams

  • Is Lark Alert a property management system?

    No, it's sensors plus alerts. There are no resident portals, no rent, no work orders, and no integrations with your property management software.

  • What do the sensors watch?

    Water and temperature. LoRaWAN leak sensors — for example, the Dragino LWL02 — report when water reaches the probe, and temperature sensors report the temperature of the space they sit in.

  • Where do the alerts go?

    To the Lark Alert iPhone app, as push alerts. Your maintenance team gets alerted on their phones.

  • What happens to an alert nobody has handled yet?

    It stays open. An incident never closes itself — it waits for a person to acknowledge and close it.

  • What if a sensor stops reporting?

    Lark Alert flags it with an offline-sensor alert. Sensors are battery powered and check in about once a day, so a sensor that goes quiet shows up as a problem instead of passing for fine.

  • Can we watch more than one building at a time?

    Yes. Organizations and sites group sensors by property and building, so one team can see a whole portfolio in one place in the Lark Alert iPhone app.

  • Does Lark Alert shut the water off?

    No. Lark Alert tells you where water showed up and keeps the incident open until someone handles it.

Get alerted when water shows up

Tell us how many buildings and units you'd want covered and we'll walk you through what Lark Alert looks like on a community.

Early access: talk to us

Prefer email or phone? sales@larkalert.com or (406) 208-5466.